Добавить скетчи SHiNE
This commit is contained in:
@@ -0,0 +1,5 @@
|
||||
# AGENTS
|
||||
|
||||
`manual_monitor_lvgl_v2.ino` is the dedicated LVGL version of the manual two-button breath monitor for Waveshare ESP32-S3-Touch-AMOLED-2.16.
|
||||
|
||||
Keep every on-screen string in English. When behavior, pins, settings, alert cadence, pause, or UI changes, update this folder's `README.md` and `../../../../reference/usb_contact_sensor_test_spec.md` in the same change.
|
||||
@@ -0,0 +1,30 @@
|
||||
# Manual Monitor LVGL v2
|
||||
|
||||
Dedicated LVGL firmware for the Waveshare ESP32-S3-Touch-AMOLED-2.16 manual breath monitor. It is separate from the legacy multi-mode GFX sketch and does not use USB D+/D- as sensor inputs.
|
||||
|
||||
## Controls
|
||||
|
||||
- `KEY2 / GPIO18`: `INHALE`, active LOW. Hold for about 1.2 seconds to open or close settings; this still accepts the INHALE phase.
|
||||
- `KEY3 / GPIO0`: `EXHALE`, active LOW. Do not hold it during reset/boot.
|
||||
- Short EXHALE completes a valid inhale/exhale cycle. Repeated INHALE or EXHALE presses are ignored.
|
||||
- Hold `KEY3 / EXHALE` for about 1.2 seconds to enter or leave conscious pause. Hold does not create an EXHALE event. Paused time is removed from the phase and cycle timers; reminders and automatic power-off are suspended.
|
||||
|
||||
## Functionality
|
||||
|
||||
- Full-screen LVGL UI with a non-flickering partial draw buffer and the board's proven built-in LVGL font path.
|
||||
- AXP2101 battery percentage, drawn battery icon, and charging marker at top right.
|
||||
- Four numeric monitor cards are label-free; the spaced `HISTORY` row shows the last five completed cycles and their exact average is rendered to tenths of a second.
|
||||
- Numeric cards use the display's straight built-in GFX digits; when AXP2101 reports an invalid `0%` while battery voltage is at least 3.3 V, the displayed percentage falls back to a voltage-derived estimate.
|
||||
- Settings for limit, confirmation tick volume, alert volume, and screen timeout (`10 / 30 / 60 sec / Always on`), stored in NVS.
|
||||
- The screen turns off after its selected idle timeout while monitoring continues. A touch or physical button wakes it.
|
||||
- After a valid phase, reminders are silent for 30 seconds, quiet every 5 seconds through 60 seconds, loud every 5 seconds through 90 seconds, and loud every 15 seconds until 6:30. Then AXP2101 shuts down the device.
|
||||
- A short average is evaluated at EXHALE, after the cycle is accepted. Consecutive short averages increase the warning sequence from one beep to five.
|
||||
|
||||
## Build or flash
|
||||
|
||||
From `SKETCH/breath_button_monitor`:
|
||||
|
||||
```bash
|
||||
NO_UPLOAD=1 ./burn.sh manual-monitor-lvgl-v2
|
||||
./burn.sh manual-monitor-lvgl-v2
|
||||
```
|
||||
Binary file not shown.
@@ -0,0 +1,191 @@
|
||||
#!/usr/bin/env bash
|
||||
set -Eeuo pipefail
|
||||
|
||||
# Build a source bundle ZIP while excluding credentials, private keys,
|
||||
# local state, generated artifacts and other likely secrets.
|
||||
#
|
||||
# Usage:
|
||||
# ./bundle.sh
|
||||
# ./bundle.sh path/to/output.zip
|
||||
#
|
||||
# Run from anywhere inside the project; the script resolves its own directory.
|
||||
|
||||
ROOT="$(cd -- "$(dirname -- "${BASH_SOURCE[0]}")" && pwd)"
|
||||
cd "$ROOT"
|
||||
|
||||
DEFAULT_OUT=0
|
||||
if [[ $# -gt 0 ]]; then
|
||||
OUT="$1"
|
||||
else
|
||||
DEFAULT_OUT=1
|
||||
OUT="SHiNE-bundle-$(date +%Y.%m.%d-%H.%M.%S).zip"
|
||||
fi
|
||||
case "$OUT" in
|
||||
/*) ;;
|
||||
*) OUT="$ROOT/$OUT" ;;
|
||||
esac
|
||||
|
||||
if ! command -v zip >/dev/null 2>&1; then
|
||||
echo "ERROR: 'zip' is required." >&2
|
||||
exit 1
|
||||
fi
|
||||
|
||||
TMP="$(mktemp -d)"
|
||||
LIST="$TMP/files.txt"
|
||||
SAFE_LIST="$TMP/safe-files.txt"
|
||||
trap 'rm -rf "$TMP"' EXIT
|
||||
|
||||
# Paths / filenames that must never be bundled.
|
||||
is_denied_path() {
|
||||
local p="/$1"
|
||||
|
||||
case "$p" in
|
||||
*/.git/*|*/.git|\
|
||||
*/.gradle/*|*/.gradle|\
|
||||
*/.gradle-home/*|*/.gradle-home|\
|
||||
*/.idea/*|*/.idea|\
|
||||
*/.vscode/*|*/.vscode|\
|
||||
*/node_modules/*|*/node_modules|\
|
||||
*/target/*|*/target|\
|
||||
*/build/*|*/build|\
|
||||
*/out/*|*/out|\
|
||||
*/bin/*|*/bin|\
|
||||
*/logs/*|*/logs|\
|
||||
*/data/*|*/data|\
|
||||
*/test-ledger/*|*/test-ledger|\
|
||||
*/.anchor/*|*/.anchor|\
|
||||
*/.yarn/*|*/.yarn|\
|
||||
*/.vendor/*|*/.vendor|\
|
||||
*/.agents/*|*/.agents|\
|
||||
*/.codex/*|*/.codex|\
|
||||
*/.claude/*|*/.claude|\
|
||||
*/deploy/backup/archive/*|\
|
||||
*/scripts/*/runs/*|\
|
||||
*/scripts/*/keypairs/*|\
|
||||
*/keys/*|\
|
||||
*/.git-local-backup/*)
|
||||
return 0
|
||||
;;
|
||||
esac
|
||||
|
||||
local base="${p##*/}"
|
||||
local lower
|
||||
lower="$(printf '%s' "$base" | tr '[:upper:]' '[:lower:]')"
|
||||
|
||||
case "$lower" in
|
||||
.env|.env.*|\
|
||||
.debug-token|\
|
||||
.npmrc|.pypirc|.netrc|\
|
||||
credentials|credentials.*|\
|
||||
secrets|secrets.*|\
|
||||
secret|secret.*|\
|
||||
id_rsa|id_dsa|id_ecdsa|id_ed25519|\
|
||||
*.pem|*.key|*.p12|*.pfx|*.jks|*.keystore|\
|
||||
*keypair*.json|\
|
||||
service-account*.json|\
|
||||
firebase-adminsdk*.json|\
|
||||
google-services.json|\
|
||||
validator.log)
|
||||
return 0
|
||||
;;
|
||||
esac
|
||||
|
||||
case "$lower" in
|
||||
*.class|*.jar|*.war|*.ear|*.o|*.a|*.so|*.dll|*.dylib|\
|
||||
*.elf|*.map|*.uf2|*.bin|*.merged.bin|\
|
||||
*.log|*.bak|*.bak.png|*.tmp|*.swp|*.swo|\
|
||||
.ds_store)
|
||||
return 0
|
||||
;;
|
||||
esac
|
||||
|
||||
return 1
|
||||
}
|
||||
|
||||
# Collect files. Prefer Git because it naturally avoids most ignored local files.
|
||||
if command -v git >/dev/null 2>&1 && git -C "$ROOT" rev-parse --is-inside-work-tree >/dev/null 2>&1; then
|
||||
git -C "$ROOT" ls-files -co --exclude-standard -z > "$TMP/files.z"
|
||||
else
|
||||
find "$ROOT" -type f -print0 > "$TMP/files.z"
|
||||
fi
|
||||
|
||||
# Convert to project-relative paths and enforce hard deny rules.
|
||||
: > "$LIST"
|
||||
while IFS= read -r -d '' f; do
|
||||
if [[ "$f" = /* ]]; then
|
||||
rel="${f#"$ROOT"/}"
|
||||
else
|
||||
rel="$f"
|
||||
fi
|
||||
|
||||
[[ "$rel" == "$OUT" ]] && continue
|
||||
[[ -z "$rel" ]] && continue
|
||||
|
||||
if is_denied_path "$rel"; then
|
||||
continue
|
||||
fi
|
||||
|
||||
printf '%s\n' "$rel" >> "$LIST"
|
||||
done < "$TMP/files.z"
|
||||
|
||||
sort -u "$LIST" -o "$LIST"
|
||||
|
||||
# Always include Gradle wrapper bootstrap, even though generic JARs are denied.
|
||||
if [[ -f "$ROOT/SHiNE-server/gradle/wrapper/gradle-wrapper.jar" ]]; then
|
||||
if ! grep -Fxq 'SHiNE-server/gradle/wrapper/gradle-wrapper.jar' "$LIST"; then
|
||||
printf '%s\n' 'SHiNE-server/gradle/wrapper/gradle-wrapper.jar' >> "$LIST"
|
||||
sort -u "$LIST" -o "$LIST"
|
||||
fi
|
||||
fi
|
||||
|
||||
# Content scan: fail closed on common credential/private-key patterns.
|
||||
# We scan only text-ish files; grep -I skips binary data.
|
||||
SECRET_RE='-----BEGIN ([A-Z0-9 ]+ )?PRIVATE KEY-----|AKIA[0-9A-Z]{16}|ASIA[0-9A-Z]{16}|gh[pousr]_[A-Za-z0-9_]{20,}|github_pat_[A-Za-z0-9_]{20,}|sk-[A-Za-z0-9_-]{20,}|xox[baprs]-[A-Za-z0-9-]{10,}|AIza[0-9A-Za-z_-]{30,}|(^|[^A-Za-z0-9])(password|passwd|pwd|secret|api[_-]?key|access[_-]?token|auth[_-]?token|private[_-]?key)[[:space:]]*[:=][[:space:]]*["'\'']?[^${[:space:]]{][^[:space:]]{7,}'
|
||||
|
||||
: > "$SAFE_LIST"
|
||||
found_secret=0
|
||||
|
||||
while IFS= read -r rel; do
|
||||
[[ -f "$ROOT/$rel" ]] || continue
|
||||
|
||||
# Files that contain examples/templates can legitimately mention secret keys
|
||||
# with placeholders. They are scanned too, but placeholder-looking values
|
||||
# are less likely to match the regex above.
|
||||
if LC_ALL=C grep -IEnq "$SECRET_RE" "$ROOT/$rel" 2>/dev/null; then
|
||||
echo "BLOCKED: possible secret in $rel" >&2
|
||||
LC_ALL=C grep -IEn "$SECRET_RE" "$ROOT/$rel" 2>/dev/null \
|
||||
| sed -E 's/(:[[:space:]]*).*/\1[REDACTED]/' \
|
||||
| head -n 3 >&2 || true
|
||||
found_secret=1
|
||||
continue
|
||||
fi
|
||||
|
||||
printf '%s\n' "$rel" >> "$SAFE_LIST"
|
||||
done < "$LIST"
|
||||
|
||||
if (( found_secret != 0 )); then
|
||||
echo >&2
|
||||
echo "Bundle NOT created because possible secrets were detected." >&2
|
||||
echo "Move secrets to ignored/local files or adjust the scanner only after review." >&2
|
||||
exit 2
|
||||
fi
|
||||
|
||||
if [[ ! -s "$SAFE_LIST" ]]; then
|
||||
echo "ERROR: no files left to bundle." >&2
|
||||
exit 3
|
||||
fi
|
||||
|
||||
if (( DEFAULT_OUT == 1 )); then
|
||||
rm -f -- "$ROOT"/SHiNE-bundle-*.zip
|
||||
else
|
||||
rm -f -- "$OUT"
|
||||
fi
|
||||
|
||||
(
|
||||
cd "$ROOT"
|
||||
zip -q -9 "$OUT" -@ < "$SAFE_LIST"
|
||||
)
|
||||
|
||||
echo "Created: $OUT"
|
||||
echo "Files: $(wc -l < "$SAFE_LIST" | tr -d ' ')"
|
||||
echo "Size: $(du -h "$OUT" | awk '{print $1}')"
|
||||
@@ -0,0 +1,443 @@
|
||||
/*
|
||||
* SPDX-FileCopyrightText: 2015-2022 Espressif Systems (Shanghai) CO LTD
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
#include <string.h>
|
||||
#include "es8311.h"
|
||||
#include "driver/gpio.h"
|
||||
#include "esp_log.h"
|
||||
#include "esp_err.h"
|
||||
#include "esp_check.h"
|
||||
#include "es8311_reg.h"
|
||||
#include "esp32-hal-i2c.h"
|
||||
|
||||
|
||||
typedef struct {
|
||||
unsigned int port;
|
||||
uint16_t dev_addr;
|
||||
} es8311_dev_t;
|
||||
|
||||
/*
|
||||
* Clock coefficient structure
|
||||
*/
|
||||
struct _coeff_div {
|
||||
uint32_t mclk; /* mclk frequency */
|
||||
uint32_t rate; /* sample rate */
|
||||
uint8_t pre_div; /* the pre divider with range from 1 to 8 */
|
||||
uint8_t pre_multi; /* the pre multiplier with 0: 1x, 1: 2x, 2: 4x, 3: 8x selection */
|
||||
uint8_t adc_div; /* adcclk divider */
|
||||
uint8_t dac_div; /* dacclk divider */
|
||||
uint8_t fs_mode; /* double speed or single speed, =0, ss, =1, ds */
|
||||
uint8_t lrck_h; /* adclrck divider and daclrck divider */
|
||||
uint8_t lrck_l;
|
||||
uint8_t bclk_div; /* sclk divider */
|
||||
uint8_t adc_osr; /* adc osr */
|
||||
uint8_t dac_osr; /* dac osr */
|
||||
};
|
||||
|
||||
/* codec hifi mclk clock divider coefficients */
|
||||
static const struct _coeff_div coeff_div[] = {
|
||||
/*!<mclk rate pre_div mult adc_div dac_div fs_mode lrch lrcl bckdiv osr */
|
||||
/* 8k */
|
||||
{12288000, 8000, 0x06, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{18432000, 8000, 0x03, 0x01, 0x03, 0x03, 0x00, 0x05, 0xff, 0x18, 0x10, 0x10},
|
||||
{16384000, 8000, 0x08, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{8192000, 8000, 0x04, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{6144000, 8000, 0x03, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{4096000, 8000, 0x02, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{3072000, 8000, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{2048000, 8000, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1536000, 8000, 0x03, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1024000, 8000, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
|
||||
/* 11.025k */
|
||||
{11289600, 11025, 0x04, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{5644800, 11025, 0x02, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{2822400, 11025, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1411200, 11025, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
|
||||
/* 12k */
|
||||
{12288000, 12000, 0x04, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{6144000, 12000, 0x02, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{3072000, 12000, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1536000, 12000, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
|
||||
/* 16k */
|
||||
{12288000, 16000, 0x03, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{18432000, 16000, 0x03, 0x01, 0x03, 0x03, 0x00, 0x02, 0xff, 0x0c, 0x10, 0x10},
|
||||
{16384000, 16000, 0x04, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{8192000, 16000, 0x02, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{6144000, 16000, 0x03, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{4096000, 16000, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{3072000, 16000, 0x03, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{2048000, 16000, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1536000, 16000, 0x03, 0x03, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1024000, 16000, 0x01, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
|
||||
/* 22.05k */
|
||||
{11289600, 22050, 0x02, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{5644800, 22050, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{2822400, 22050, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1411200, 22050, 0x01, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{705600, 22050, 0x01, 0x03, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
|
||||
/* 24k */
|
||||
{12288000, 24000, 0x02, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{18432000, 24000, 0x03, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{6144000, 24000, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{3072000, 24000, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1536000, 24000, 0x01, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
|
||||
/* 32k */
|
||||
{12288000, 32000, 0x03, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{18432000, 32000, 0x03, 0x02, 0x03, 0x03, 0x00, 0x02, 0xff, 0x0c, 0x10, 0x10},
|
||||
{16384000, 32000, 0x02, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{8192000, 32000, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{6144000, 32000, 0x03, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{4096000, 32000, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{3072000, 32000, 0x03, 0x03, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{2048000, 32000, 0x01, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1536000, 32000, 0x03, 0x03, 0x01, 0x01, 0x01, 0x00, 0x7f, 0x02, 0x10, 0x10},
|
||||
{1024000, 32000, 0x01, 0x03, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
|
||||
/* 44.1k */
|
||||
{11289600, 44100, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{5644800, 44100, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{2822400, 44100, 0x01, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1411200, 44100, 0x01, 0x03, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
|
||||
/* 48k */
|
||||
{12288000, 48000, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{18432000, 48000, 0x03, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{6144000, 48000, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{3072000, 48000, 0x01, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1536000, 48000, 0x01, 0x03, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
|
||||
/* 64k */
|
||||
{12288000, 64000, 0x03, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{18432000, 64000, 0x03, 0x02, 0x03, 0x03, 0x01, 0x01, 0x7f, 0x06, 0x10, 0x10},
|
||||
{16384000, 64000, 0x01, 0x00, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{8192000, 64000, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{6144000, 64000, 0x01, 0x02, 0x03, 0x03, 0x01, 0x01, 0x7f, 0x06, 0x10, 0x10},
|
||||
{4096000, 64000, 0x01, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{3072000, 64000, 0x01, 0x03, 0x03, 0x03, 0x01, 0x01, 0x7f, 0x06, 0x10, 0x10},
|
||||
{2048000, 64000, 0x01, 0x03, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1536000, 64000, 0x01, 0x03, 0x01, 0x01, 0x01, 0x00, 0xbf, 0x03, 0x18, 0x18},
|
||||
{1024000, 64000, 0x01, 0x03, 0x01, 0x01, 0x01, 0x00, 0x7f, 0x02, 0x10, 0x10},
|
||||
|
||||
/* 88.2k */
|
||||
{11289600, 88200, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{5644800, 88200, 0x01, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{2822400, 88200, 0x01, 0x03, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1411200, 88200, 0x01, 0x03, 0x01, 0x01, 0x01, 0x00, 0x7f, 0x02, 0x10, 0x10},
|
||||
|
||||
/* 96k */
|
||||
{12288000, 96000, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{18432000, 96000, 0x03, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{6144000, 96000, 0x01, 0x02, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{3072000, 96000, 0x01, 0x03, 0x01, 0x01, 0x00, 0x00, 0xff, 0x04, 0x10, 0x10},
|
||||
{1536000, 96000, 0x01, 0x03, 0x01, 0x01, 0x01, 0x00, 0x7f, 0x02, 0x10, 0x10},
|
||||
};
|
||||
|
||||
static const char *TAG = "ES8311";
|
||||
|
||||
static inline esp_err_t es8311_write_reg(es8311_handle_t dev, uint8_t reg_addr, uint8_t data)
|
||||
{
|
||||
es8311_dev_t *es = (es8311_dev_t *) dev;
|
||||
const uint8_t write_buf[2] = {reg_addr, data};
|
||||
return i2cWrite(es->port, es->dev_addr, write_buf, sizeof(write_buf), 1000);
|
||||
}
|
||||
|
||||
static inline esp_err_t es8311_read_reg(es8311_handle_t dev, uint8_t reg_addr, uint8_t *reg_value)
|
||||
{
|
||||
es8311_dev_t *es = (es8311_dev_t *) dev;
|
||||
size_t readCount = 0;
|
||||
return i2cWriteReadNonStop(es->port, es->dev_addr, ®_addr, 1, reg_value, 1, 1000, &readCount);
|
||||
}
|
||||
|
||||
/*
|
||||
* look for the coefficient in coeff_div[] table
|
||||
*/
|
||||
static int get_coeff(uint32_t mclk, uint32_t rate)
|
||||
{
|
||||
for (int i = 0; i < (sizeof(coeff_div) / sizeof(coeff_div[0])); i++) {
|
||||
if (coeff_div[i].rate == rate && coeff_div[i].mclk == mclk) {
|
||||
return i;
|
||||
}
|
||||
}
|
||||
|
||||
return -1;
|
||||
}
|
||||
|
||||
esp_err_t es8311_sample_frequency_config(es8311_handle_t dev, int mclk_frequency, int sample_frequency)
|
||||
{
|
||||
uint8_t regv;
|
||||
|
||||
/* Get clock coefficients from coefficient table */
|
||||
int coeff = get_coeff(mclk_frequency, sample_frequency);
|
||||
|
||||
if (coeff < 0) {
|
||||
ESP_LOGE(TAG, "Unable to configure sample rate %dHz with %dHz MCLK", sample_frequency, mclk_frequency);
|
||||
return ESP_ERR_INVALID_ARG;
|
||||
}
|
||||
|
||||
const struct _coeff_div *const selected_coeff = &coeff_div[coeff];
|
||||
|
||||
/* register 0x02 */
|
||||
ESP_RETURN_ON_ERROR(es8311_read_reg(dev, ES8311_CLK_MANAGER_REG02, ®v), TAG, "I2C read/write error");
|
||||
regv &= 0x07;
|
||||
regv |= (selected_coeff->pre_div - 1) << 5;
|
||||
regv |= selected_coeff->pre_multi << 3;
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_CLK_MANAGER_REG02, regv), TAG, "I2C read/write error");
|
||||
|
||||
/* register 0x03 */
|
||||
const uint8_t reg03 = (selected_coeff->fs_mode << 6) | selected_coeff->adc_osr;
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_CLK_MANAGER_REG03, reg03), TAG, "I2C read/write error");
|
||||
|
||||
/* register 0x04 */
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_CLK_MANAGER_REG04, selected_coeff->dac_osr), TAG, "I2C read/write error");
|
||||
|
||||
/* register 0x05 */
|
||||
const uint8_t reg05 = ((selected_coeff->adc_div - 1) << 4) | (selected_coeff->dac_div - 1);
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_CLK_MANAGER_REG05, reg05), TAG, "I2C read/write error");
|
||||
|
||||
/* register 0x06 */
|
||||
ESP_RETURN_ON_ERROR(es8311_read_reg(dev, ES8311_CLK_MANAGER_REG06, ®v), TAG, "I2C read/write error");
|
||||
regv &= 0xE0;
|
||||
|
||||
if (selected_coeff->bclk_div < 19) {
|
||||
regv |= (selected_coeff->bclk_div - 1) << 0;
|
||||
} else {
|
||||
regv |= (selected_coeff->bclk_div) << 0;
|
||||
}
|
||||
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_CLK_MANAGER_REG06, regv), TAG, "I2C read/write error");
|
||||
|
||||
/* register 0x07 */
|
||||
ESP_RETURN_ON_ERROR(es8311_read_reg(dev, ES8311_CLK_MANAGER_REG07, ®v), TAG, "I2C read/write error");
|
||||
regv &= 0xC0;
|
||||
regv |= selected_coeff->lrck_h << 0;
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_CLK_MANAGER_REG07, regv), TAG, "I2C read/write error");
|
||||
|
||||
/* register 0x08 */
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_CLK_MANAGER_REG08, selected_coeff->lrck_l), TAG, "I2C read/write error");
|
||||
|
||||
return ESP_OK;
|
||||
}
|
||||
|
||||
static esp_err_t es8311_clock_config(es8311_handle_t dev, const es8311_clock_config_t *const clk_cfg, es8311_resolution_t res)
|
||||
{
|
||||
uint8_t reg06;
|
||||
uint8_t reg01 = 0x3F; // Enable all clocks
|
||||
int mclk_hz;
|
||||
|
||||
/* Select clock source for internal MCLK and determine its frequency */
|
||||
if (clk_cfg->mclk_from_mclk_pin) {
|
||||
mclk_hz = clk_cfg->mclk_frequency;
|
||||
} else {
|
||||
mclk_hz = clk_cfg->sample_frequency * (int)res * 2;
|
||||
reg01 |= BIT(7); // Select BCLK (a.k.a. SCK) pin
|
||||
}
|
||||
|
||||
if (clk_cfg->mclk_inverted) {
|
||||
reg01 |= BIT(6); // Invert MCLK pin
|
||||
}
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_CLK_MANAGER_REG01, reg01), TAG, "I2C read/write error");
|
||||
|
||||
ESP_RETURN_ON_ERROR(es8311_read_reg(dev, ES8311_CLK_MANAGER_REG06, ®06), TAG, "I2C read/write error");
|
||||
if (clk_cfg->sclk_inverted) {
|
||||
reg06 |= BIT(5);
|
||||
} else {
|
||||
reg06 &= ~BIT(5);
|
||||
}
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_CLK_MANAGER_REG06, reg06), TAG, "I2C read/write error");
|
||||
|
||||
/* Configure clock dividers */
|
||||
return es8311_sample_frequency_config(dev, mclk_hz, clk_cfg->sample_frequency);
|
||||
}
|
||||
|
||||
static esp_err_t es8311_resolution_config(const es8311_resolution_t res, uint8_t *reg)
|
||||
{
|
||||
switch (res) {
|
||||
case ES8311_RESOLUTION_16:
|
||||
*reg |= (3 << 2);
|
||||
break;
|
||||
case ES8311_RESOLUTION_18:
|
||||
*reg |= (2 << 2);
|
||||
break;
|
||||
case ES8311_RESOLUTION_20:
|
||||
*reg |= (1 << 2);
|
||||
break;
|
||||
case ES8311_RESOLUTION_24:
|
||||
*reg |= (0 << 2);
|
||||
break;
|
||||
case ES8311_RESOLUTION_32:
|
||||
*reg |= (4 << 2);
|
||||
break;
|
||||
default:
|
||||
return ESP_ERR_INVALID_ARG;
|
||||
}
|
||||
return ESP_OK;
|
||||
}
|
||||
|
||||
static esp_err_t es8311_fmt_config(es8311_handle_t dev, const es8311_resolution_t res_in, const es8311_resolution_t res_out)
|
||||
{
|
||||
uint8_t reg09 = 0; // SDP In
|
||||
uint8_t reg0a = 0; // SDP Out
|
||||
|
||||
ESP_LOGI(TAG, "ES8311 in Slave mode and I2S format");
|
||||
uint8_t reg00;
|
||||
ESP_RETURN_ON_ERROR(es8311_read_reg(dev, ES8311_RESET_REG00, ®00), TAG, "I2C read/write error");
|
||||
reg00 &= 0xBF;
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_RESET_REG00, reg00), TAG, "I2C read/write error"); // Slave serial port - default
|
||||
|
||||
/* Setup SDP In and Out resolution */
|
||||
es8311_resolution_config(res_in, ®09);
|
||||
es8311_resolution_config(res_out, ®0a);
|
||||
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_SDPIN_REG09, reg09), TAG, "I2C read/write error");
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_SDPOUT_REG0A, reg0a), TAG, "I2C read/write error");
|
||||
|
||||
return ESP_OK;
|
||||
}
|
||||
|
||||
esp_err_t es8311_microphone_config(es8311_handle_t dev, bool digital_mic)
|
||||
{
|
||||
uint8_t reg14 = 0x1A; // enable analog MIC and max PGA gain
|
||||
|
||||
/* PDM digital microphone enable or disable */
|
||||
if (digital_mic) {
|
||||
reg14 |= BIT(6);
|
||||
}
|
||||
es8311_write_reg(dev, ES8311_ADC_REG17, 0xC8); // Set ADC gain @todo move this to ADC config section
|
||||
|
||||
return es8311_write_reg(dev, ES8311_SYSTEM_REG14, reg14);
|
||||
}
|
||||
|
||||
esp_err_t es8311_init(es8311_handle_t dev, const es8311_clock_config_t *const clk_cfg, const es8311_resolution_t res_in, const es8311_resolution_t res_out)
|
||||
{
|
||||
ESP_RETURN_ON_FALSE(
|
||||
(clk_cfg->sample_frequency >= 8000) && (clk_cfg->sample_frequency <= 96000),
|
||||
ESP_ERR_INVALID_ARG, TAG, "ES8311 init needs frequency in interval [8000; 96000] Hz"
|
||||
);
|
||||
if (!clk_cfg->mclk_from_mclk_pin) {
|
||||
ESP_RETURN_ON_FALSE(res_out == res_in, ESP_ERR_INVALID_ARG, TAG, "Resolution IN/OUT must be equal if MCLK is taken from SCK pin");
|
||||
}
|
||||
|
||||
|
||||
/* Reset ES8311 to its default */
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_RESET_REG00, 0x1F), TAG, "I2C read/write error");
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_RESET_REG00, 0x00), TAG, "I2C read/write error");
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_RESET_REG00, 0x80), TAG, "I2C read/write error"); // Power-on command
|
||||
|
||||
/* Setup clock: source, polarity and clock dividers */
|
||||
ESP_RETURN_ON_ERROR(es8311_clock_config(dev, clk_cfg, res_out), TAG, "");
|
||||
|
||||
/* Setup audio format (fmt): master/slave, resolution, I2S */
|
||||
ESP_RETURN_ON_ERROR(es8311_fmt_config(dev, res_in, res_out), TAG, "");
|
||||
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_SYSTEM_REG0D, 0x01), TAG, "I2C read/write error"); // Power up analog circuitry - NOT default
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_SYSTEM_REG0E, 0x02), TAG, "I2C read/write error"); // Enable analog PGA, enable ADC modulator - NOT default
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_SYSTEM_REG12, 0x00), TAG, "I2C read/write error"); // power-up DAC - NOT default
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_SYSTEM_REG13, 0x10), TAG, "I2C read/write error"); // Enable output to HP drive - NOT default
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_ADC_REG1C, 0x6A), TAG, "I2C read/write error"); // ADC Equalizer bypass, cancel DC offset in digital domain
|
||||
ESP_RETURN_ON_ERROR(es8311_write_reg(dev, ES8311_DAC_REG37, 0x08), TAG, "I2C read/write error"); // Bypass DAC equalizer - NOT default
|
||||
|
||||
return ESP_OK;
|
||||
}
|
||||
|
||||
void es8311_delete(es8311_handle_t dev)
|
||||
{
|
||||
free(dev);
|
||||
}
|
||||
|
||||
esp_err_t es8311_voice_volume_set(es8311_handle_t dev, int volume, int *volume_set)
|
||||
{
|
||||
if (volume < 0) {
|
||||
volume = 0;
|
||||
} else if (volume > 100) {
|
||||
volume = 100;
|
||||
}
|
||||
|
||||
int reg32;
|
||||
if (volume == 0) {
|
||||
reg32 = 0;
|
||||
} else {
|
||||
reg32 = ((volume) * 256 / 100) - 1;
|
||||
}
|
||||
|
||||
// provide user with real volume set
|
||||
if (volume_set != NULL) {
|
||||
*volume_set = volume;
|
||||
}
|
||||
return es8311_write_reg(dev, ES8311_DAC_REG32, reg32);
|
||||
}
|
||||
|
||||
esp_err_t es8311_voice_volume_get(es8311_handle_t dev, int *volume)
|
||||
{
|
||||
uint8_t reg32;
|
||||
ESP_RETURN_ON_ERROR(es8311_read_reg(dev, ES8311_DAC_REG32, ®32), TAG, "I2C read/write error");
|
||||
|
||||
if (reg32 == 0) {
|
||||
*volume = 0;
|
||||
} else {
|
||||
*volume = ((reg32 * 100) / 256) + 1;
|
||||
}
|
||||
return ESP_OK;
|
||||
}
|
||||
|
||||
esp_err_t es8311_voice_mute(es8311_handle_t dev, bool mute)
|
||||
{
|
||||
uint8_t reg31;
|
||||
ESP_RETURN_ON_ERROR(es8311_read_reg(dev, ES8311_DAC_REG31, ®31), TAG, "I2C read/write error");
|
||||
|
||||
if (mute) {
|
||||
reg31 |= BIT(6) | BIT(5);
|
||||
} else {
|
||||
reg31 &= ~(BIT(6) | BIT(5));
|
||||
}
|
||||
|
||||
return es8311_write_reg(dev, ES8311_DAC_REG31, reg31);
|
||||
}
|
||||
|
||||
esp_err_t es8311_microphone_gain_set(es8311_handle_t dev, es8311_mic_gain_t gain_db)
|
||||
{
|
||||
return es8311_write_reg(dev, ES8311_ADC_REG16, gain_db); // ADC gain scale up
|
||||
}
|
||||
|
||||
esp_err_t es8311_voice_fade(es8311_handle_t dev, const es8311_fade_t fade)
|
||||
{
|
||||
uint8_t reg37;
|
||||
ESP_RETURN_ON_ERROR(es8311_read_reg(dev, ES8311_DAC_REG37, ®37), TAG, "I2C read/write error");
|
||||
reg37 &= 0x0F;
|
||||
reg37 |= (fade << 4);
|
||||
return es8311_write_reg(dev, ES8311_DAC_REG37, reg37);
|
||||
}
|
||||
|
||||
esp_err_t es8311_microphone_fade(es8311_handle_t dev, const es8311_fade_t fade)
|
||||
{
|
||||
uint8_t reg15;
|
||||
ESP_RETURN_ON_ERROR(es8311_read_reg(dev, ES8311_ADC_REG15, ®15), TAG, "I2C read/write error");
|
||||
reg15 &= 0x0F;
|
||||
reg15 |= (fade << 4);
|
||||
return es8311_write_reg(dev, ES8311_ADC_REG15, reg15);
|
||||
}
|
||||
|
||||
void es8311_register_dump(es8311_handle_t dev)
|
||||
{
|
||||
for (int reg = 0; reg < 0x4A; reg++) {
|
||||
uint8_t value;
|
||||
ESP_ERROR_CHECK(es8311_read_reg(dev, reg, &value));
|
||||
printf("REG:%02x: %02x", reg, value);
|
||||
}
|
||||
}
|
||||
|
||||
es8311_handle_t es8311_create(const unsigned int port, const uint16_t dev_addr)
|
||||
{
|
||||
es8311_dev_t *sensor = (es8311_dev_t *) calloc(1, sizeof(es8311_dev_t));
|
||||
sensor->port = port;
|
||||
sensor->dev_addr = dev_addr;
|
||||
return (es8311_handle_t) sensor;
|
||||
}
|
||||
@@ -0,0 +1,227 @@
|
||||
/*
|
||||
* SPDX-FileCopyrightText: 2015-2022 Espressif Systems (Shanghai) CO LTD
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
/**
|
||||
* @file
|
||||
* @brief ES8311 driver
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "esp_types.h"
|
||||
#include "esp_err.h"
|
||||
|
||||
/* ES8311 address: CE pin low - 0x18, CE pin high - 0x19 */
|
||||
#define ES8311_ADDRRES_0 0x18u // Leaving this here for backward compatibility
|
||||
#define ES8311_ADDRESS_0 0x18u
|
||||
#define ES8311_ADDRESS_1 0x19u
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
typedef void *es8311_handle_t;
|
||||
|
||||
typedef enum {
|
||||
ES8311_MIC_GAIN_MIN = -1,
|
||||
ES8311_MIC_GAIN_0DB,
|
||||
ES8311_MIC_GAIN_6DB,
|
||||
ES8311_MIC_GAIN_12DB,
|
||||
ES8311_MIC_GAIN_18DB,
|
||||
ES8311_MIC_GAIN_24DB,
|
||||
ES8311_MIC_GAIN_30DB,
|
||||
ES8311_MIC_GAIN_36DB,
|
||||
ES8311_MIC_GAIN_42DB,
|
||||
ES8311_MIC_GAIN_MAX
|
||||
} es8311_mic_gain_t;
|
||||
|
||||
typedef enum {
|
||||
ES8311_FADE_OFF = 0,
|
||||
ES8311_FADE_4LRCK, // 4LRCK means ramp 0.25dB/4LRCK
|
||||
ES8311_FADE_8LRCK,
|
||||
ES8311_FADE_16LRCK,
|
||||
ES8311_FADE_32LRCK,
|
||||
ES8311_FADE_64LRCK,
|
||||
ES8311_FADE_128LRCK,
|
||||
ES8311_FADE_256LRCK,
|
||||
ES8311_FADE_512LRCK,
|
||||
ES8311_FADE_1024LRCK,
|
||||
ES8311_FADE_2048LRCK,
|
||||
ES8311_FADE_4096LRCK,
|
||||
ES8311_FADE_8192LRCK,
|
||||
ES8311_FADE_16384LRCK,
|
||||
ES8311_FADE_32768LRCK,
|
||||
ES8311_FADE_65536LRCK
|
||||
} es8311_fade_t;
|
||||
|
||||
typedef enum es8311_resolution_t {
|
||||
ES8311_RESOLUTION_16 = 16,
|
||||
ES8311_RESOLUTION_18 = 18,
|
||||
ES8311_RESOLUTION_20 = 20,
|
||||
ES8311_RESOLUTION_24 = 24,
|
||||
ES8311_RESOLUTION_32 = 32
|
||||
} es8311_resolution_t;
|
||||
|
||||
typedef struct es8311_clock_config_t {
|
||||
bool mclk_inverted;
|
||||
bool sclk_inverted;
|
||||
bool mclk_from_mclk_pin; // true: from MCLK pin (pin no. 2), false: from SCLK pin (pin no. 6)
|
||||
int mclk_frequency; // This parameter is ignored if MCLK is taken from SCLK pin
|
||||
int sample_frequency; // in Hz
|
||||
} es8311_clock_config_t;
|
||||
|
||||
/**
|
||||
* @brief Initialize ES8311
|
||||
*
|
||||
* There are two ways of providing Master Clock (MCLK) signal to ES8311 in Slave Mode:
|
||||
* 1. From MCLK pin:
|
||||
* For flexible scenarios. A clock signal from I2S master is routed to MCLK pin.
|
||||
* Its frequency must be defined in clk_cfg->mclk_frequency parameter.
|
||||
* 2. From SCLK pin:
|
||||
* For simpler scenarios. ES8311 takes its clock from SCK pin. MCLK pin does not have to be connected.
|
||||
* In this case, res_in must equal res_out; clk_cfg->mclk_frequency parameter is ignored
|
||||
* and MCLK is calculated as MCLK = clk_cfg->sample_frequency * res_out * 2.
|
||||
* Not all sampling frequencies are supported in this mode.
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
* @param[in] clk_cfg Clock configuration
|
||||
* @param[in] res_in Input serial port resolution
|
||||
* @param[in] res_out Output serial port resolution
|
||||
* @return
|
||||
* - ESP_OK success
|
||||
* - ESP_ERR_INVALID_ARG Sample frequency or resolution invalid
|
||||
* - Else fail
|
||||
*/
|
||||
esp_err_t es8311_init(es8311_handle_t dev, const es8311_clock_config_t *const clk_cfg, const es8311_resolution_t res_in,
|
||||
const es8311_resolution_t res_out);
|
||||
|
||||
/**
|
||||
* @brief Set output volume
|
||||
*
|
||||
* Volume paramter out of <0, 100> interval will be truncated.
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
* @param[in] volume Set volume (0 ~ 100)
|
||||
* @param[out] volume_set Volume that was set. Same as volume, unless volume is outside of <0, 100> interval.
|
||||
* This parameter can be set to NULL, if user does not need this information.
|
||||
*
|
||||
* @return
|
||||
* - ESP_OK success
|
||||
* - Else fail
|
||||
*/
|
||||
esp_err_t es8311_voice_volume_set(es8311_handle_t dev, int volume, int *volume_set);
|
||||
|
||||
/**
|
||||
* @brief Get output volume
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
* @param[out] volume get volume (0 ~ 100)
|
||||
*
|
||||
* @return
|
||||
* - ESP_OK success
|
||||
* - Else fail
|
||||
*/
|
||||
esp_err_t es8311_voice_volume_get(es8311_handle_t dev, int *volume);
|
||||
|
||||
/**
|
||||
* @brief Print out ES8311 register content
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
*/
|
||||
void es8311_register_dump(es8311_handle_t dev);
|
||||
|
||||
/**
|
||||
* @brief Mute ES8311 output
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
* @param[in] enable true: mute, false: don't mute
|
||||
* @return
|
||||
* - ESP_OK success
|
||||
* - Else fail
|
||||
*/
|
||||
esp_err_t es8311_voice_mute(es8311_handle_t dev, bool enable);
|
||||
|
||||
/**
|
||||
* @brief Set Microphone gain
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
* @param[in] gain_db Microphone gain
|
||||
* @return
|
||||
* - ESP_OK success
|
||||
* - Else fail
|
||||
*/
|
||||
esp_err_t es8311_microphone_gain_set(es8311_handle_t dev, es8311_mic_gain_t gain_db);
|
||||
|
||||
/**
|
||||
* @brief Configure microphone
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
* @param[in] digital_mic Set to true for digital microphone
|
||||
* @return
|
||||
* - ESP_OK success
|
||||
* - Else fail
|
||||
*/
|
||||
esp_err_t es8311_microphone_config(es8311_handle_t dev, bool digital_mic);
|
||||
|
||||
/**
|
||||
* @brief Configure sampling frequency
|
||||
*
|
||||
* @note This function is called by es8311_init().
|
||||
* Call this function explicitly only if you want to change sample frequency during runtime.
|
||||
* @param dev ES8311 handle
|
||||
* @param[in] mclk_frequency MCLK frequency in [Hz] (MCLK or SCLK pin, depending on bit register01[7])
|
||||
* @param[in] sample_frequency Required sample frequency in [Hz], e.g. 44100, 22050...
|
||||
* @return
|
||||
* - ESP_OK success
|
||||
* - ESP_ERR_INVALID_ARG cannot set clock dividers for given MCLK and sampling frequency
|
||||
* - Else I2C read/write error
|
||||
*/
|
||||
esp_err_t es8311_sample_frequency_config(es8311_handle_t dev, int mclk_frequency, int sample_frequency);
|
||||
|
||||
/**
|
||||
* @brief Configure fade in/out for ADC: voice
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
* @param[in] fade Fade ramp rate
|
||||
* @return
|
||||
* - ESP_OK success
|
||||
* - Else I2C read/write error
|
||||
*/
|
||||
esp_err_t es8311_voice_fade(es8311_handle_t dev, const es8311_fade_t fade);
|
||||
|
||||
/**
|
||||
* @brief Configure fade in/out for DAC: microphone
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
* @param[in] fade Fade ramp rate
|
||||
* @return
|
||||
* - ESP_OK success
|
||||
* - Else I2C read/write error
|
||||
*/
|
||||
esp_err_t es8311_microphone_fade(es8311_handle_t dev, const es8311_fade_t fade);
|
||||
|
||||
/**
|
||||
* @brief Create ES8311 object and return its handle
|
||||
*
|
||||
* @param[in] port I2C port number
|
||||
* @param[in] dev_addr I2C device address of ES8311
|
||||
*
|
||||
* @return
|
||||
* - NULL Fail
|
||||
* - Others Success
|
||||
*/
|
||||
es8311_handle_t es8311_create(const unsigned int port, const uint16_t dev_addr);
|
||||
|
||||
/**
|
||||
* @brief Delete ES8311 object
|
||||
*
|
||||
* @param dev ES8311 handle
|
||||
*/
|
||||
void es8311_delete(es8311_handle_t dev);
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
@@ -0,0 +1,76 @@
|
||||
/*
|
||||
* SPDX-FileCopyrightText: 2015-2021 Espressif Systems (Shanghai) CO LTD
|
||||
*
|
||||
* SPDX-License-Identifier: Apache-2.0
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
/*
|
||||
* ES8311_REGISTER NAME_REG_REGISTER ADDRESS
|
||||
*/
|
||||
#define ES8311_RESET_REG00 0x00 /*reset digital,csm,clock manager etc.*/
|
||||
|
||||
/*
|
||||
* Clock Scheme Register definition
|
||||
*/
|
||||
#define ES8311_CLK_MANAGER_REG01 0x01 /* select clk src for mclk, enable clock for codec */
|
||||
#define ES8311_CLK_MANAGER_REG02 0x02 /* clk divider and clk multiplier */
|
||||
#define ES8311_CLK_MANAGER_REG03 0x03 /* adc fsmode and osr */
|
||||
#define ES8311_CLK_MANAGER_REG04 0x04 /* dac osr */
|
||||
#define ES8311_CLK_MANAGER_REG05 0x05 /* clk divier for adc and dac */
|
||||
#define ES8311_CLK_MANAGER_REG06 0x06 /* bclk inverter and divider */
|
||||
#define ES8311_CLK_MANAGER_REG07 0x07 /* tri-state, lrck divider */
|
||||
#define ES8311_CLK_MANAGER_REG08 0x08 /* lrck divider */
|
||||
/*
|
||||
* SDP
|
||||
*/
|
||||
#define ES8311_SDPIN_REG09 0x09 /* dac serial digital port */
|
||||
#define ES8311_SDPOUT_REG0A 0x0A /* adc serial digital port */
|
||||
/*
|
||||
* SYSTEM
|
||||
*/
|
||||
#define ES8311_SYSTEM_REG0B 0x0B /* system */
|
||||
#define ES8311_SYSTEM_REG0C 0x0C /* system */
|
||||
#define ES8311_SYSTEM_REG0D 0x0D /* system, power up/down */
|
||||
#define ES8311_SYSTEM_REG0E 0x0E /* system, power up/down */
|
||||
#define ES8311_SYSTEM_REG0F 0x0F /* system, low power */
|
||||
#define ES8311_SYSTEM_REG10 0x10 /* system */
|
||||
#define ES8311_SYSTEM_REG11 0x11 /* system */
|
||||
#define ES8311_SYSTEM_REG12 0x12 /* system, Enable DAC */
|
||||
#define ES8311_SYSTEM_REG13 0x13 /* system */
|
||||
#define ES8311_SYSTEM_REG14 0x14 /* system, select DMIC, select analog pga gain */
|
||||
/*
|
||||
* ADC
|
||||
*/
|
||||
#define ES8311_ADC_REG15 0x15 /* ADC, adc ramp rate, dmic sense */
|
||||
#define ES8311_ADC_REG16 0x16 /* ADC */
|
||||
#define ES8311_ADC_REG17 0x17 /* ADC, volume */
|
||||
#define ES8311_ADC_REG18 0x18 /* ADC, alc enable and winsize */
|
||||
#define ES8311_ADC_REG19 0x19 /* ADC, alc maxlevel */
|
||||
#define ES8311_ADC_REG1A 0x1A /* ADC, alc automute */
|
||||
#define ES8311_ADC_REG1B 0x1B /* ADC, alc automute, adc hpf s1 */
|
||||
#define ES8311_ADC_REG1C 0x1C /* ADC, equalizer, hpf s2 */
|
||||
/*
|
||||
* DAC
|
||||
*/
|
||||
#define ES8311_DAC_REG31 0x31 /* DAC, mute */
|
||||
#define ES8311_DAC_REG32 0x32 /* DAC, volume */
|
||||
#define ES8311_DAC_REG33 0x33 /* DAC, offset */
|
||||
#define ES8311_DAC_REG34 0x34 /* DAC, drc enable, drc winsize */
|
||||
#define ES8311_DAC_REG35 0x35 /* DAC, drc maxlevel, minilevel */
|
||||
#define ES8311_DAC_REG37 0x37 /* DAC, ramprate */
|
||||
/*
|
||||
*GPIO
|
||||
*/
|
||||
#define ES8311_GPIO_REG44 0x44 /* GPIO, dac2adc for test */
|
||||
#define ES8311_GP_REG45 0x45 /* GP CONTROL */
|
||||
/*
|
||||
* CHIP
|
||||
*/
|
||||
#define ES8311_CHD1_REGFD 0xFD /* CHIP ID1 */
|
||||
#define ES8311_CHD2_REGFE 0xFE /* CHIP ID2 */
|
||||
#define ES8311_CHVER_REGFF 0xFF /* VERSION */
|
||||
#define ES8311_CHD1_REGFD 0xFD /* CHIP ID1 */
|
||||
|
||||
#define ES8311_MAX_REGISTER 0xFF
|
||||
@@ -0,0 +1,123 @@
|
||||
#include <Arduino.h>
|
||||
#include <Wire.h>
|
||||
#include <Preferences.h>
|
||||
#include <Arduino_GFX_Library.h>
|
||||
#include <TouchDrvCSTXXX.hpp>
|
||||
#include <lvgl.h>
|
||||
#define XPOWERS_CHIP_AXP2101
|
||||
#include <XPowersLib.h>
|
||||
#include "ESP_I2S.h"
|
||||
#include "es8311.h"
|
||||
|
||||
void setup();
|
||||
void loop();
|
||||
|
||||
// Dedicated LVGL v2 of the manual two-button breath monitor.
|
||||
#define PIN_LCD_CS 12
|
||||
#define PIN_LCD_SCLK 38
|
||||
#define PIN_LCD_D0 4
|
||||
#define PIN_LCD_D1 5
|
||||
#define PIN_LCD_D2 6
|
||||
#define PIN_LCD_D3 7
|
||||
#define PIN_LCD_RST 2
|
||||
#define PIN_I2C_SDA 15
|
||||
#define PIN_I2C_SCL 14
|
||||
#define PIN_TP_INT 11
|
||||
#define PIN_INHALE 18
|
||||
#define PIN_EXHALE 0
|
||||
#define PIN_PA 46
|
||||
#define PIN_I2S_BCLK 9
|
||||
#define PIN_I2S_LRCK 45
|
||||
#define PIN_I2S_DOUT 8
|
||||
#define PIN_I2S_DIN 10
|
||||
#define PIN_I2S_MCLK 42
|
||||
|
||||
static constexpr uint16_t DISP_W = 480, DISP_H = 480;
|
||||
static constexpr uint32_t LVGL_TICK_MS = 2, UI_MS = 120, HOLD_PAUSE_MS = 1200;
|
||||
static constexpr uint32_t DEBOUNCE_MS = 45, BATT_MS = 5000;
|
||||
static constexpr uint32_t QUIET_START_MS = 30000, LOUD_START_MS = 60000;
|
||||
static constexpr uint32_t SLOW_LOUD_MS = 90000, POWER_OFF_MS = 390000;
|
||||
static constexpr uint16_t LIMITS[] = {5, 7, 10, 15, 20};
|
||||
static constexpr uint32_t SCREEN_TIMEOUTS[] = {10000, 30000, 60000, 0};
|
||||
static const char *SCREEN_TIMEOUT_NAMES[] = {"10 sec", "30 sec", "60 sec", "Always on"};
|
||||
static const int16_t TICK_VOLUME[] = {0, 40, 80, 140, 220, 320, 440, 580, 720, 800, 1600};
|
||||
static const int16_t ALERT_VOLUME[] = {0, 150, 300, 500, 800, 12000, 12000, 12000, 12000, 12000, 12000};
|
||||
|
||||
Arduino_DataBus *gBus = new Arduino_ESP32QSPI(PIN_LCD_CS, PIN_LCD_SCLK, PIN_LCD_D0, PIN_LCD_D1, PIN_LCD_D2, PIN_LCD_D3);
|
||||
Arduino_CO5300 *gfx = new Arduino_CO5300(gBus, PIN_LCD_RST, 0, DISP_W, DISP_H, 0, 0, 0, 0);
|
||||
TouchDrvCST92xx gTouch;
|
||||
XPowersPMU gPower;
|
||||
I2SClass gI2s;
|
||||
Preferences gPrefs;
|
||||
|
||||
struct Button { int pin; bool raw = false; bool stable = false; uint32_t changed = 0; uint32_t pressed = 0; };
|
||||
static Button gInhale{PIN_INHALE}, gExhale{PIN_EXHALE};
|
||||
enum class Screen : uint8_t { Home, Monitor, Settings };
|
||||
static Screen gScreen = Screen::Home;
|
||||
static bool gPowerReady = false, gAudioReady = false, gTouchDown = false;
|
||||
static bool gScreenOn = true, gPaused = false, gHaveInhale = false;
|
||||
static uint32_t gPauseStarted = 0, gPhaseStarted = 0, gCycleStarted = 0, gLastActivity = 0, gLastUi = 0, gLastBatt = 0, gLastReminder = 0;
|
||||
static uint8_t gLimit = 2, gTick = 3, gAlert = 10, gScreenTimeout = 1;
|
||||
static uint32_t gCycles[5] = {}; static uint8_t gCycleCount = 0, gCycleNext = 0, gShortStreak = 0;
|
||||
static lv_disp_draw_buf_t gDrawBuf; static lv_color_t *gBuf1 = nullptr, *gBuf2 = nullptr;
|
||||
static lv_obj_t *gRoot = nullptr, *gPhase = nullptr, *gPhaseValue = nullptr, *gAverage = nullptr, *gAverageValue = nullptr;
|
||||
static lv_obj_t *gElapsedValue = nullptr, *gLimitValue = nullptr, *gLastFive = nullptr, *gState = nullptr;
|
||||
static lv_obj_t *gBatteryText = nullptr, *gBatteryFill = nullptr, *gBolt = nullptr;
|
||||
static bool gDirectNumbersPending = false;
|
||||
static char gDirectPhase[16] = "0.0 s", gDirectAverage[16] = "--", gDirectElapsed[12] = "00:00", gDirectLimit[16] = "10.0 s";
|
||||
|
||||
static lv_color_t color(uint32_t c) { return lv_color_hex(c); }
|
||||
static void flush(lv_disp_drv_t *d, const lv_area_t *a, lv_color_t *p) {
|
||||
uint32_t w = a->x2-a->x1+1, h = a->y2-a->y1+1;
|
||||
#if LV_COLOR_16_SWAP != 0
|
||||
gfx->draw16bitBeRGBBitmap(a->x1,a->y1,(uint16_t *)&p->full,w,h);
|
||||
#else
|
||||
gfx->draw16bitRGBBitmap(a->x1,a->y1,(uint16_t *)&p->full,w,h);
|
||||
#endif
|
||||
lv_disp_flush_ready(d);
|
||||
}
|
||||
static void tick(void *) { lv_tick_inc(LVGL_TICK_MS); }
|
||||
static void touchRead(lv_indev_drv_t *, lv_indev_data_t *d) {
|
||||
int16_t x=0,y=0; bool down = gTouch.getPoint(&x,&y,1)>0;
|
||||
if (down && !gTouchDown) { gTouchDown=true; gLastActivity=millis(); if (!gScreenOn) { gfx->setBrightness(220); gScreenOn=true; } }
|
||||
if (!down) gTouchDown=false;
|
||||
d->state=down ? LV_INDEV_STATE_PR : LV_INDEV_STATE_REL; d->point.x=x; d->point.y=y;
|
||||
}
|
||||
static void card(lv_obj_t *o, uint32_t bg=0x142331) { lv_obj_set_style_bg_color(o,color(bg),0); lv_obj_set_style_border_color(o,color(0x365264),0); lv_obj_set_style_border_width(o,1,0); lv_obj_set_style_radius(o,14,0); lv_obj_clear_flag(o,LV_OBJ_FLAG_SCROLLABLE); }
|
||||
static lv_obj_t *label(lv_obj_t *p,const char *s,const lv_font_t *f,uint32_t c) {
|
||||
lv_obj_t *o=lv_label_create(p);
|
||||
lv_label_set_text(o,s);
|
||||
lv_obj_set_style_text_font(o,f,0);
|
||||
lv_obj_set_style_text_color(o,color(c),0);
|
||||
return o;
|
||||
}
|
||||
static lv_obj_t *panel(int x,int y,int w,int h,uint32_t bg=0x142331) { lv_obj_t *o=lv_obj_create(gRoot); lv_obj_set_pos(o,x,y); lv_obj_set_size(o,w,h); card(o,bg); return o; }
|
||||
static void fmt(char *out,size_t n,uint32_t ms) { snprintf(out,n,"%lu.%01lu s",(unsigned long)(ms/1000),(unsigned long)((ms%1000)/100)); }
|
||||
static uint32_t average() { uint64_t total=0; for(uint8_t i=0;i<gCycleCount;i++) total+=gCycles[i]; return gCycleCount ? (uint32_t)((total+gCycleCount/2)/gCycleCount) : 0; }
|
||||
static void loadSettings() { gPrefs.begin("manual-lvgl",false); gLimit=min<uint8_t>(4,gPrefs.getUChar("limit",2)); gTick=min<uint8_t>(10,gPrefs.getUChar("tick",3)); gAlert=min<uint8_t>(10,gPrefs.getUChar("alert",10)); gScreenTimeout=min<uint8_t>(3,gPrefs.getUChar("screen",1)); }
|
||||
static void saveSettings() { gPrefs.putUChar("limit",gLimit); gPrefs.putUChar("tick",gTick); gPrefs.putUChar("alert",gAlert); gPrefs.putUChar("screen",gScreenTimeout); }
|
||||
static void initPower() { gPowerReady=gPower.begin(Wire,AXP2101_SLAVE_ADDRESS,PIN_I2C_SDA,PIN_I2C_SCL); if(!gPowerReady)return; gPower.disableIRQ(XPOWERS_AXP2101_ALL_IRQ); gPower.setChargeTargetVoltage(3); gPower.clearIrqStatus(); gPower.enableBattDetection(); gPower.enableBattVoltageMeasure(); gPower.enableVbusVoltageMeasure(); }
|
||||
static int battery() { if(!gPowerReady || !gPower.isBatteryConnect())return -1; int percent=constrain(gPower.getBatteryPercent(),0,100); uint16_t mv=gPower.getBattVoltage(); if(percent==0 && mv>=3300) return constrain((int)((mv-3300UL)*100UL/900UL),1,100); return percent; }
|
||||
static void initAudio() { pinMode(PIN_PA,OUTPUT); digitalWrite(PIN_PA,HIGH); gI2s.setPins(PIN_I2S_BCLK,PIN_I2S_LRCK,PIN_I2S_DOUT,PIN_I2S_DIN,PIN_I2S_MCLK); if(!gI2s.begin(I2S_MODE_STD,16000,I2S_DATA_BIT_WIDTH_16BIT,I2S_SLOT_MODE_STEREO,I2S_STD_SLOT_BOTH))return; es8311_handle_t h=es8311_create(0,ES8311_ADDRRES_0); if(!h)return; es8311_clock_config_t c={false,false,true,4096000,16000}; gAudioReady=es8311_init(h,&c,ES8311_RESOLUTION_16,ES8311_RESOLUTION_16)==ESP_OK; if(gAudioReady){es8311_voice_volume_set(h,100,nullptr);es8311_voice_mute(h,false);} }
|
||||
static void beep(uint16_t hz,uint16_t count,int16_t amp) { if(!gAudioReady||amp<=0)return; static int16_t buf[1600*2]; count=min<uint16_t>(count,1600); for(uint16_t i=0;i<count;i++){int16_t v=(int16_t)(sinf(6.2831853f*hz*i/16000.0f)*amp);buf[i*2]=v;buf[i*2+1]=v;} gI2s.write((uint8_t *)buf,count*4); }
|
||||
static void quiet() { beep(880,480,TICK_VOLUME[gTick]); } static void loud(){beep(1200,1600,ALERT_VOLUME[gAlert]);}
|
||||
static void batteryUi() { if(!gBatteryText)return; int p=battery(); char t[8]; snprintf(t,sizeof(t),p<0?"--":"%d%%",p); lv_label_set_text(gBatteryText,t); if(gBatteryFill)lv_obj_set_width(gBatteryFill,p>0?max(2,min(26,p*26/100)):0); if(gBolt)lv_obj_set_style_opa(gBolt,(gPowerReady&&gPower.isCharging())?LV_OPA_COVER:LV_OPA_TRANSP,0); }
|
||||
static void topBar(const char *title) { label(gRoot,title,&lv_font_montserrat_24,0xFFFFFF); lv_obj_align(lv_obj_get_child(gRoot,0),LV_ALIGN_TOP_LEFT,26,20); gBatteryText=label(gRoot,"--",&lv_font_montserrat_16,0xC9D3DE); lv_obj_set_pos(gBatteryText,297,22); if(gPowerReady){static const lv_point_t bolt[]={{6,0},{1,9},{5,9},{2,18},{10,7},{6,7}};gBolt=lv_line_create(gRoot);lv_line_set_points(gBolt,bolt,6);lv_obj_set_pos(gBolt,337,17);lv_obj_set_style_line_width(gBolt,2,0);lv_obj_set_style_line_color(gBolt,color(0xFFD34D),0);lv_obj_set_style_line_rounded(gBolt,true,0);} lv_obj_t *b=lv_obj_create(gRoot);lv_obj_set_pos(b,349,24);lv_obj_set_size(b,32,16);lv_obj_set_style_bg_opa(b,LV_OPA_TRANSP,0);lv_obj_set_style_border_color(b,color(0xC9D3DE),0);lv_obj_set_style_border_width(b,2,0);lv_obj_set_style_radius(b,4,0);lv_obj_clear_flag(b,LV_OBJ_FLAG_SCROLLABLE); lv_obj_t *cap=lv_obj_create(gRoot);lv_obj_set_pos(cap,381,28);lv_obj_set_size(cap,4,8);lv_obj_set_style_bg_color(cap,color(0xC9D3DE),0);lv_obj_set_style_border_width(cap,0,0);lv_obj_set_style_radius(cap,2,0); gBatteryFill=lv_obj_create(gRoot);lv_obj_set_pos(gBatteryFill,352,27);lv_obj_set_size(gBatteryFill,2,10);lv_obj_set_style_bg_color(gBatteryFill,color(0x38B26D),0);lv_obj_set_style_border_width(gBatteryFill,0,0);lv_obj_set_style_radius(gBatteryFill,2,0); batteryUi(); }
|
||||
static void clearUi() { lv_obj_clean(lv_scr_act()); gRoot=lv_scr_act(); lv_obj_set_style_bg_color(gRoot,color(0x08111B),0);lv_obj_set_style_bg_opa(gRoot,LV_OPA_COVER,0);lv_obj_set_style_pad_all(gRoot,0,0); gBatteryText=gBatteryFill=gBolt=nullptr; }
|
||||
static void drawDirectNumber(int x,int y,int w,int h,const char *text,uint16_t textColor,uint8_t size) { gfx->fillRect(x+2,y+2,w-4,h-4,0x142331); gfx->setFont(); gfx->setTextSize(size); gfx->setTextColor(textColor); int tx=x+(w-(int)strlen(text)*6*size)/2; gfx->setCursor(max(x+6,tx),y+(h-8*size)/2+7*size); gfx->print(text); }
|
||||
static void drawDirectNumbers() { if(!gDirectNumbersPending || gScreen!=Screen::Monitor || !gScreenOn)return; drawDirectNumber(24,202,204,88,gDirectPhase,0xFFFF,4); drawDirectNumber(252,202,204,88,gDirectAverage,0xFFFF,4); drawDirectNumber(24,306,204,72,gDirectElapsed,0xFFFF,4); drawDirectNumber(252,306,204,72,gDirectLimit,0xFFE0,4); gDirectNumbersPending=false; }
|
||||
static void enterMonitor(lv_event_t *) { gScreen=Screen::Monitor; gLastActivity=millis(); clearUi(); topBar("MANUAL MONITOR"); lv_obj_t *hero=panel(24,72,432,112,0x102A36); gState=label(hero,"READY",&lv_font_montserrat_28,0x4FB3FF);lv_obj_align(gState,LV_ALIGN_TOP_MID,0,18); lv_obj_t *hint=label(hero,"KEY2: INHALE KEY3: EXHALE",&lv_font_montserrat_14,0xB8C7D2);lv_obj_align(hint,LV_ALIGN_BOTTOM_MID,0,-17); lv_obj_t *a=panel(24,202,204,88);gPhaseValue=label(a,"",&lv_font_montserrat_32,0xFFFFFF); lv_obj_t *b=panel(252,202,204,88);gAverageValue=label(b,"",&lv_font_montserrat_32,0xFFFFFF); lv_obj_t *c=panel(24,306,204,72);gElapsedValue=label(c,"",&lv_font_montserrat_28,0xFFFFFF); lv_obj_t *d=panel(252,306,204,72);gLimitValue=label(d,"",&lv_font_montserrat_28,0xFFD34D); lv_obj_t *last=panel(24,394,432,60);gLastFive=label(last,"HISTORY: --",&lv_font_montserrat_16,0xD7E3EA);lv_obj_align(gLastFive,LV_ALIGN_CENTER,0,0); gDirectNumbersPending=true; }
|
||||
static void home(lv_event_t *); static void settings(lv_event_t *);
|
||||
static lv_obj_t *button(lv_obj_t *p,const char *text,int x,int y,int w,int h,uint32_t bg,lv_event_cb_t cb) { lv_obj_t *b=lv_btn_create(p);lv_obj_set_pos(b,x,y);lv_obj_set_size(b,w,h);card(b,bg);lv_obj_add_event_cb(b,cb,LV_EVENT_CLICKED,nullptr);lv_obj_t *l=label(b,text,&lv_font_montserrat_20,0xFFFFFF);lv_obj_center(l);return b; }
|
||||
static void home(lv_event_t *) { gScreen=Screen::Home;clearUi();topBar("BREATH MONITOR");lv_obj_t *intro=panel(24,78,432,84,0x102A36);lv_obj_t *i=label(intro,"Two external buttons",&lv_font_montserrat_22,0xFFFFFF);lv_obj_align(i,LV_ALIGN_TOP_MID,0,14);i=label(intro,"Manual breathing cadence monitor",&lv_font_montserrat_14,0xB8C7D2);lv_obj_align(i,LV_ALIGN_BOTTOM_MID,0,-14);button(gRoot,"START MANUAL MONITOR",24,188,432,82,0x28775E,enterMonitor);button(gRoot,"SETTINGS",24,290,208,58,0x214D69,settings);button(gRoot,"ABOUT",248,290,208,58,0x403C68,[](lv_event_t *){});lv_obj_t *h=panel(24,374,432,70);i=label(h,"Hold EXHALE to pause / resume",&lv_font_montserrat_16,0xFFD34D);lv_obj_align(i,LV_ALIGN_TOP_MID,0,12);i=label(h,"Screen can turn off; measurement continues",&lv_font_montserrat_14,0xB8C7D2);lv_obj_align(i,LV_ALIGN_BOTTOM_MID,0,-12); }
|
||||
static void settingChanged(lv_event_t *e){uint8_t *v=(uint8_t *)lv_event_get_user_data(e);*v=lv_slider_get_value(lv_event_get_target(e));saveSettings();}
|
||||
static void settings(lv_event_t *) {gScreen=Screen::Settings;clearUi();topBar("SETTINGS");lv_obj_t *list=lv_obj_create(gRoot);lv_obj_set_pos(list,20,68);lv_obj_set_size(list,440,352);card(list,0x10202D);lv_obj_set_style_pad_all(list,16,0);lv_obj_set_flex_flow(list,LV_FLEX_FLOW_COLUMN);lv_obj_set_style_pad_row(list,18,0);struct Item{const char *name;uint8_t *v;uint8_t max;};Item items[]={{"Breath limit",&gLimit,4},{"Cycle tick",&gTick,10},{"Alert volume",&gAlert,10},{"Screen timeout",&gScreenTimeout,3}};for(auto &it:items){lv_obj_t *row=lv_obj_create(list);lv_obj_set_size(row,400,66);card(row,0x172C3C);lv_obj_t *n=label(row,it.name,&lv_font_montserrat_16,0xFFFFFF);lv_obj_set_pos(n,12,8);lv_obj_t *s=lv_slider_create(row);lv_obj_set_pos(s,12,34);lv_obj_set_size(s,376,18);lv_slider_set_range(s,0,it.max);lv_slider_set_value(s,*it.v,LV_ANIM_OFF);lv_obj_add_event_cb(s,settingChanged,LV_EVENT_VALUE_CHANGED,it.v);}button(gRoot,"BACK",150,430,180,38,0x214D69,home);}
|
||||
static void toggleSettingsFromKey(){ if(gScreen==Screen::Monitor) settings(nullptr); else if(gScreen==Screen::Settings) enterMonitor(nullptr); }
|
||||
static void addCycle(uint32_t ms){gCycles[gCycleNext]=ms;gCycleNext=(gCycleNext+1)%5;if(gCycleCount<5)gCycleCount++;uint32_t a=average();if(a && a<LIMITS[gLimit]*1000UL){gShortStreak=min<uint8_t>(5,gShortStreak+1);for(uint8_t i=0;i<gShortStreak;i++){loud();delay(80);}}else gShortStreak=0;}
|
||||
static void phase(bool inhale){uint32_t now=millis();if(gPaused)return;if(inhale){if(gHaveInhale)return;gHaveInhale=true;gPhaseStarted=now;if(!gCycleStarted)gCycleStarted=now;quiet();}else{if(!gHaveInhale)return;uint32_t cycle=now-gCycleStarted;addCycle(cycle);gHaveInhale=false;gCycleStarted=now;gPhaseStarted=now;quiet();}gLastReminder=now;}
|
||||
static void togglePause(){uint32_t now=millis();if(!gPaused){gPaused=true;gPauseStarted=now;}else{uint32_t delta=now-gPauseStarted;if(gPhaseStarted)gPhaseStarted+=delta;if(gCycleStarted)gCycleStarted+=delta;gLastReminder+=delta;gPaused=false;}gLastActivity=now;}
|
||||
static void poll(Button &b,bool inhale){uint32_t now=millis();bool raw=digitalRead(b.pin)==LOW;if(raw!=b.raw){b.raw=raw;b.changed=now;}if(b.stable==b.raw||now-b.changed<DEBOUNCE_MS)return;b.stable=b.raw;if(b.stable){b.pressed=now;gLastActivity=now;if(!gScreenOn){gScreenOn=true;gfx->setBrightness(220);}if(gScreen==Screen::Monitor&&inhale)phase(true);return;}uint32_t held=now-b.pressed;if(inhale&&held>=HOLD_PAUSE_MS){toggleSettingsFromKey();return;}if(gScreen!=Screen::Monitor)return;if(!inhale&&held>=HOLD_PAUSE_MS)togglePause();else if(!inhale)phase(false);}
|
||||
static void refresh(){if(gScreen!=Screen::Monitor)return;uint32_t now=millis(),phaseMs=gPhaseStarted&&!gPaused?now-gPhaseStarted:0;char s[100]; if(gPaused)lv_label_set_text(gState,"PAUSED");else if(!gHaveInhale)lv_label_set_text(gState,"WAITING FOR INHALE");else lv_label_set_text(gState,"INHALE - PRESS EXHALE");fmt(gDirectPhase,sizeof(gDirectPhase),phaseMs);uint32_t a=average();if(a)fmt(gDirectAverage,sizeof(gDirectAverage),a);else snprintf(gDirectAverage,sizeof(gDirectAverage),"--");snprintf(gDirectLimit,sizeof(gDirectLimit),"%u.%01u s",LIMITS[gLimit],0);uint32_t elapsed=gCycleStarted&&!gPaused?now-gCycleStarted:0;snprintf(gDirectElapsed,sizeof(gDirectElapsed),"%02lu:%02lu",(unsigned long)(elapsed/60000),(unsigned long)((elapsed/1000)%60));size_t used=snprintf(s,sizeof(s),"HISTORY:");for(uint8_t i=0;i<gCycleCount&&used<sizeof(s);i++){uint8_t j=(gCycleNext+5-gCycleCount+i)%5;used+=snprintf(s+used,sizeof(s)-used," %lu.%01lu",(unsigned long)(gCycles[j]/1000),(unsigned long)((gCycles[j]%1000)/100));}if(!gCycleCount)snprintf(s,sizeof(s),"HISTORY: --");lv_label_set_text(gLastFive,s);gDirectNumbersPending=true;}
|
||||
static void reminders(){if(gScreen!=Screen::Monitor||gPaused||!gPhaseStarted)return;uint32_t now=millis(),age=now-gPhaseStarted;if(age<QUIET_START_MS||now-gLastReminder<((age<SLOW_LOUD_MS)?5000:15000))return;gLastReminder=now;if(age<LOUD_START_MS)quiet();else if(age<POWER_OFF_MS)loud();else{gfx->setBrightness(0);if(gPowerReady)gPower.shutdown();esp_deep_sleep_start();}}
|
||||
void setup(){Serial.begin(115200);Wire.begin(PIN_I2C_SDA,PIN_I2C_SCL);initPower();pinMode(PIN_INHALE,INPUT_PULLUP);pinMode(PIN_EXHALE,INPUT_PULLUP);initAudio();gfx->begin();gBus->writeC8D8(0x36,0xA0);gfx->setBrightness(220);gTouch.setPins(PIN_TP_INT,-1);gTouch.begin(Wire,0x5A,PIN_I2C_SDA,PIN_I2C_SCL);gTouch.setMaxCoordinates(DISP_W,DISP_H);gTouch.setSwapXY(true);gTouch.setMirrorXY(true,false);loadSettings();lv_init();gBuf1=(lv_color_t *)heap_caps_malloc(DISP_W*40*sizeof(lv_color_t),MALLOC_CAP_DMA);gBuf2=(lv_color_t *)heap_caps_malloc(DISP_W*40*sizeof(lv_color_t),MALLOC_CAP_DMA);lv_disp_draw_buf_init(&gDrawBuf,gBuf1,gBuf2,DISP_W*40);static lv_disp_drv_t dd;lv_disp_drv_init(&dd);dd.hor_res=DISP_W;dd.ver_res=DISP_H;dd.flush_cb=flush;dd.draw_buf=&gDrawBuf;lv_disp_drv_register(&dd);static lv_indev_drv_t id;lv_indev_drv_init(&id);id.type=LV_INDEV_TYPE_POINTER;id.read_cb=touchRead;lv_indev_drv_register(&id);const esp_timer_create_args_t ta={.callback=&tick,.name="lvgl_tick"};esp_timer_handle_t timer;esp_timer_create(&ta,&timer);esp_timer_start_periodic(timer,LVGL_TICK_MS*1000);gLastActivity=millis();home(nullptr);}
|
||||
void loop(){uint32_t now=millis();poll(gInhale,true);poll(gExhale,false);reminders();if(now-gLastUi>=UI_MS){gLastUi=now;refresh();}if(now-gLastBatt>=BATT_MS){gLastBatt=now;batteryUi();}uint32_t timeout=SCREEN_TIMEOUTS[gScreenTimeout];if(gScreenOn&&timeout&&now-gLastActivity>=timeout){gScreenOn=false;gfx->setBrightness(0);}lv_timer_handler();drawDirectNumbers();delay(5);}
|
||||
Reference in New Issue
Block a user